CAN I INSTALL A BATHTUB MYSELF? FACTORS TO CONSIDER AS WELL AS STEPS

Can I Install a Bathtub Myself? Factors to Consider As Well As Steps

Can I Install a Bathtub Myself? Factors to Consider As Well As Steps

Blog Article

View Website

This great article following next relating to How to Install a Bathtub Yourself is pretty much motivating. Don't miss it.


Installing A Bathtub
Installing a bathtub isn't precisely rocket science, however it does call for strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably difficult project. If the old bathtub is conveniently obtainable, the job can move quickly; if you have to open a wall surface to eliminate the old tub and place the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Make sure you have certified on your own for the work as well as fit attempting it. As opposed to working with a service provider to take control of a halfway-completed task, it is much better to consider utilizing one before you begin. Possibilities are you may require a specialist plumber to make tube links.
This post will assist you install a brand-new bath tub in your bathroom if you have actually currently gotten a new tub and also do not need to transform the setup of your previous water system pipes.
Your tools and also product checklist should consist of the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you require to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, switch on the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather troublesome because of the limited gain access to that is often the case.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
    Prior to carrying on to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

    Suitable New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipes.
    If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
    Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Secure the tap in place with the producer given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Setting up the Bathtub


    Using both wood boards under its feet, position the bath tub in the called for placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
    The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the bath tub until the spirit level reads degree.
    To mount faucets, fit the bottom of the furthest adaptable tap adapter to the ideal supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
    Turn on the water supply and also inspect all joints and new pipework for leakages and tighten them if essential. Fill up the bath tub as well as likewise inspect the overflow electrical outlet as well as the regular outlet for leakages.
    Lastly, repair the bathroom paneling as explained in the maker's instruction manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of at least when as this will certainly settle it right into its final placement.

    Getting ready for the Installation


    First of all, the supporting framework supplied with the bathroom should be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid pressure on the bath tub.
    Fit the flexible tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the provided washers.
    Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its last placement.

    Tiling Around the Bath tub


    In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break a stiff seal, triggering the water to permeate the wall between the bath and also the tiling, leading to complications with dampness and feasible leakages to the ceiling listed below.
    You can pick from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not consider this activity prior to securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I'm very eager about Installing A Bathtub and I am hoping you appreciated the piece. Feel free to take a moment to share this page if you appreciated it. Thank you for taking the time to read it.




    Recurring Service Plans


    Report this page